 | Liner lock
poolpartmart liner lock is avalible
in two types for fitting either
under the coping stone
when building a new pool
or if your refurbishing a pool
and don't want to remove
the copings a side mount
version should be used
|
|
 | Underlay
A 4mm liner pool underlay from poolpartmart
comes in rolls 25mts long and 2mts wide
layed under your liner will hlpe to protect
the liner and give a softer floor to walk on
recomended when fitting a replacement
liner to an old pool |
|
 | Liner repair kits
poolpartmart liner Swimming Pool Repair kits and patches can be used underwater
All surfaces must be clean. Cut round corners on patch. For inflatables and light gauge vinyls, apply adhesive to patch sparingly and press tightly to surface to be repaired. Allow to dry for 24 hours.
A face mask or underwater goggles should always be used when going underwater to make repairs.
For deep underwater repairs, cut round corners on patch. Apply adhesive to patch and fold patch over upon itself. When you reach the damaged area under water unfold patch and apply immediately to liner, squeezing out all water bubbles. Do not disturb patch for at least 48 hours. Allow 4-7 days for full cure.
For quick and easy vinyl repairs without liquid adhesive, use Boxer Vinyl Plastic Pool Patches. This is a clear tape where you peel off the paper backing and apply immediately. Vinyl Plastic Pool Patches are excellent for other applications such as vinyl upholstery and waterbeds.
|
|
 | Liners 20 thou
poolpartmart 20 thou
domestic liners are designed for use
in private domestic pools with normal
bathing loads, run below 29°C (84°F) only,
and have a five year pro-rata guarantee
against material and manufacturing fault.
All our pool liners are manufactured using
the best European and American vinyls
available. Exacting standards are used in
the fabrication techniques in our modern
factory.
Most liners are packed in scrap
material and cardboard boxes with dimensions
in mm of 900L x 700W x 400D. As
a guide for despatch weights: 0.5mm material
weighs approx. 0.63kg per square
metre and 0.75mm weighs 0.94kg per
square metre.
It is recommended when installing a liner, to
treat the walls and floor with a suitable
algaecide/fungicide to help prevent microbial
attack or staining of the liner. Ensure the
surfaces you are installing the liner on are
compatible with PVC materials. Do not
attempt to install a pool liner in temperatures
less than 50°F (10°C) as the P.V.C. material
will become stiff and difficult to install.
Liner patterns cannot be matched along the
weld lines, therefore combination liners are
not recommended.
Please note: Darker patterned materials may
show a thin white line along the edge of the
weld due to the white base material flowing
during the welding process. This is normal
and is not a fault. |
|
| Liners 30 thou
poolpartmart 30 thou
domestic liners are designed for use
in private domestic pools with normal
bathing loads, run below 29°C (84°F) only,
and have a five year pro-rata guarantee
against material and manufacturing fault.
All our pool liners are manufactured using
the best European and American vinyls
available. Exacting standards are used in
the fabrication techniques in our modern
factory.
Most liners are packed in scrap
material and cardboard boxes with dimensions
in mm of 900L x 700W x 400D. As
a guide for despatch weights: 0.5mm material
weighs approx. 0.63kg per square
metre and 0.75mm weighs 0.94kg per
square metre.
It is recommended when installing a liner, to
treat the walls and floor with a suitable
algaecide/fungicide to help prevent microbial
attack or staining of the liner. Ensure the
surfaces you are installing the liner on are
compatible with PVC materials. Do not
attempt to install a pool liner in temperatures
less than 50°F (10°C) as the P.V.C. material
will become stiff and difficult to install.
Liner patterns cannot be matched along the
weld lines, therefore combination liners are
not recommended.
Please note: Darker patterned materials may
show a thin white line along the edge of the
weld due to the white base material flowing
during the welding process. This is normal
and is not a fault. |
|
